Your furnace is an integral part of your home. Without one, you wouldn’t be able to keep warm during cold weather. Yet furnaces can have some issues that are more typical than others.

Let’s review these issues and discuss what they might cost to fix so you know before you contact an HVAC technician. Some of the most common furnace repair problems involve:

  • Furnace won’t turn on
  • Furnace doesn’t stay lit
  • Furnace won’t blow hot air
  • Furnace won’t turn off

1. The Furnace Will Not Turn On

There are a couple of reasons why your furnace won’t turn on, so make sure to go through all of them.

  • Is your thermostat set correctly? Make sure it’s on “heat,” “auto” and that your desired temperature is higher than the room’s current temperature. If you have a programmable thermostat, make sure it has new batteries.
  • Is the circuit breaker tripped? Your furnace can’t operate if it doesn’t have electricity. Reset the switch if it’s facing the outside of the electrical panel.
  • Is the furnace switch off? Your furnace has a power switch located on or close to it. Since this switch looks like a light switch, it’s easy to unintentionally turn it off. If it was off, it might take your furnace a few minutes to turn on.
  • Is the air filter clean? A dusty air filter can create a lot of issues for your furnace. Get a new one if you can’t see light through it.

Estimated Repair Cost

This problem can be complex, so the estimated cost to repair it depends on what’s wrong.

2. The Furnace Isn’t Staying Lit

Your furnace uses a specific sequence when it begins heating your home.

  1. Your thermostat notices the temperature has dropped and tells your furnace to start running.
  2. The draft inducer fan activates to bring in fresh air for combustion.
  3. The gas valve opens for the burners, which are ignited electronically.
  4. The flame sensor tells your furnace the burners have been lit.

If something is wrong during the sequence, your furnace will shut off as a preventive measure.

A couple of possible causes for this problem include:

  • Dirty or malfunctioning flame sensor. If the sensor doesn’t sense a flame, it will turn off your furnace to keep natural gas from spilling into your home. The ignition process corrodes flame sensors as time passes. While cleaning during annual furnace maintenance can help, yours may eventually need to be taken out and changed.
  • Bad limit switch. This safety feature will shut off your furnace if it detects backdrafting. Backdrafting is hazardous, because carbon monoxide and natural gas can leak into your home. These switches can malfunction due to age, damage or dust accumulation.
  • Old thermostat. If your thermostat isn’t working properly, your furnace won’t be able to operate.
  • Dirty air filter. A dirty air filter can limit airflow and force your furnace to shut down to prevent overheating. Make sure to replace yours every 30 to 90 days, or whenever you can’t see light through it.

Estimated Repair Cost

These costs are estimates, so it’s necessary to note yours may vary based on your furnace’s brand and model.

  • Flame sensor: $350–$500
  • Limit switch: $150–$300
  • Thermostat: $150–$350
  • Furnace filter: $10-$30

3. The Furnace Won’t Blow Hot Air

In many cases, this problem is linked to an incorrect thermostat setting or a dusty air filter that’s restricting airflow. Follow the steps above to fix the problem.

4. The Furnace Isn’t Shutting Off

If it’s very chilly outside or you like your home to be warm, your furnace may be working for a long time.

If this isn’t the case, make sure your thermostat is set correctly and running properly. If your fan setting is at “on,” the blower motor will be running even when the furnace isn’t, so it’ll seem like your furnace is running all the time.

Alternatively, there might be a problem with the blower motor or your ductwork may be leaking air, forcing your furnace to run constantly to make up for the lost air.

Estimated Repair Cost

These costs are approximations, so it’s important to note yours may vary based on your furnace’s brand and model.

  • New blower motor: $250–$800
  • Seal ductwork: varies based on square footage

Retro HVAC Service & Installation Will Work Hard to Solve Your Furnace Issues as Soon as Possible

Furnace issues can be an expensive headache, but not when you call Retro HVAC Service & Installation. We’ve been providing the quality, affordable furnace repair Philadelphia homeowners have relied on since year. Contact us at 267-277-3851 to receive your free estimate today.